SERIES 101 Series Terminal Screw No. Lock Washer No. Stop Screw No. Lockwasher No. Mounting Screw No. 24 02016-26-C3 – 02016-10 02015-6 02016-87 Color Lens Red Green Amber White Blue Bulb Part No. 100-93-5 100-93-6 100-93-7 100-93-31 100-93-36 245-8-910 31 Four Hole Mount 02016-1-C3 None 02016-10 02015-6 02016-102 31 Single Hole 02016-1-C3 02015-1-C3 02016-10 02015-6 * 101 02016-26 – – – 02016-103 LENS FOR SERIES 20P LAMPS Panel Thickness 1/16" 1/8" 3 /16" Part No. 001022-1 001022-2 001022-3 Panel Thickness Part No. WATERPROOF  MOUNT Coil A B C D E F K Nominal Voltage 24VDC 24VDC 48VDC 125VDC/120VAC 125VDC 250VDC 125VDC Part No. 002008-12A-3 002008-12B-3 002008-12C-3 002008-12D-3 002008-12E-3 002008-12F-3 002008-14D-3 SERIES 24 TRIP COIL FOR  LOR Nominal Voltage 24VDC 48VDC 125VDC 250VDC 120VAC 250VAC Part No. 349A556G01 349A556G01 349A556G02 349A556G02 349A556G10 349A556G10 SERIES WL-2 TRIP COIL FOR  LOR Waterproof Mount Requires Special Shaft  Consult Factory Series 31 Single Hole Mount 3 /16" Max 02017-8 * Nut 02017-4 (2) Locking Ring 03007-1 (1) Lockwasher 02015-5 Series Code No. Size Title Engraving Position Engraving Notes 101 04 2.38" x 2.88" 12 characters max 6 characters max For waterproof mount use Code No. 5 W-2* 61 Remov. Handle 2" x 3" See Below See Below W-2* 62 Target 2" x 3" See Below See Below No engraving available at 0° position. Target colors red & green. W-2 and WL-2* 63 Standard 2" x 3" See Below See Below Type W 73 2" x 2.375" See Below See Below NOTE:   Radial lines etched on nameplates will be blackened in. On engraved nameplates, only the radial lines for engraved positions will be blackened in. 7 TYPE W TYPE W-2 1 4 6 2 3 5 • Nameplate Engraving Locations (1-7) • Engraved Nameplates for W ONLY •   Use This Chart to Specify Engraving. Indicate Engraving Locations by Line Numbers Shown. Engraving Location No. 1 2 3 4 5 6 7 No. of Letter Spaces Per Line 8 4 4 8 4 4 16 • Nameplate Engraving Locations (1-18) • Engraved Nameplates for W-2 ONLY • Use This Chart to Specify Engraving. Indicate Engraving Locations by Line Numbers Shown. • Character Space Allowance is the same for Code 61, 62, and 63 Nameplates. • Line 12 is Not Available on Code 62 (Target) Nameplates. Engraving Location No. 1-5, 7-11 6, 12 13-18 No. of Letter Spaces Per Line 6 14 26 12 15 16 13 18 14 17 11 10 9 8 7 6 1 2 3 4 5 SERIES  101 TYPE W-2, WL-2 AND W